采购单
进口自吸式无堵塞排污泵【进口品牌哪个好】
进口自吸式无堵塞排污泵产品概述：
进口自吸式无堵塞排污泵,主要由泵体, 叶轮、后盖、机械密封、泵轴、轴承座、进口阀、气液分离管、加水阀门、进、排接管等组成。泵的结构见图。自吸排污泵的工作原理：泵体内设有储液腔，并通过上方的回流孔和下方的循环孔与泵工作腔相通，构成泵的轴向加流外混式系统。泵停止工作后，泵内腔已储有一定容积的液体。当泵起动时，有关当局内的储液在叶轮的作用下，夹带着空气被向上抛出，液体通过气液分离管的网格回流到工作腔，气体被排出泵外，使泵内形成一定的真空度，达到自吸的作用。
Self-priming non-blocking sewage pump is mainly composed of pump body, impeller, back cover, mechanical seal, pump shaft, bearing seat, inlet valve, gas-liquid separation pipe, water supply valve, inlet and outlet nozzle, etc. The structure of the pump is shown in the diagram. The working principle of self-priming sewage pump is that the pump body is equipped with a liquid storage chamber, and communicates with the pump working chamber through the upper reflux hole and the lower circulation hole, forming an axial flow-adding and external mixing system of the pump. After the pump stops working, there is a certain volume of liquid in the pump chamber. When the pump starts, the liquid stored in the relevant authorities is thrown upward with air under the action of impeller. The liquid flows back to the working chamber through the mesh of the gas-liquid separator tube, and the gas is discharged out of the pump, so that a certain degree of vacuum is formed in the pump and self-priming is achieved.
进口自吸式无堵塞排污泵适用范围：
1、环境温度≤50℃，介质温度≤80℃特殊要求可达200℃
2、介质PH值铸铁材质为6--9级，不锈钢为2-13。
3、介质重度不超过1240千克/m3.
4、自吸排污泵自吸高度不能超过规定值4.5-5.5米，吸入管长度为≤10米。
5、自吸排污泵通过能力悬浮颗粒直径为泵口径的60%,纤维长度为泵口径的5倍。
1. The special requirements of ambient temperature (< 50 C) and medium temperature (< 80 C) can be up to 200 (?)
2. Medium PH value cast iron is grade 6-9 and stainless steel is grade 2-13.
3. The medium weight should not exceed 1240 kg/m3.
4. The self-priming height of the self-priming sewage pump should not exceed the prescribed value of 4.5-5.5 meters, and the length of the suction tube should be less than 10 meters.
5. The passing capacity of self-priming sewage pump is 60% of the diameter of suspended particles, and the length of fibers is 5 times of the diameter of the pump.
解决方案：
1.吸入管路越短越好，最长不超过10M。
2.此泵若用于抽吸较稠较粘的浆液后，需清洗泵腔，防止泵内留下沉淀物。
3.自吸泵第一次使用，仍需将泵腔灌满水。
4.常规运行3000小时后，需对水泵进行拆检保养，必要时更换不宜再用的易损件。
5.此泵可定做直联式，同心度高，稳定性增强，亦更为经济，不过维修稍嫌麻烦。
6.环境温度≤45℃，介质温度≤60℃。
7.介质PH值铸铁泵为6～9，不锈钢自吸泵为1～14。
8.通过颗粒最大直径为自吸泵口径的60%，纤维长度为口径的5倍。
9.介质中杂质总重量不超过介质总重量的15%，介质比重不超过1240千克/立方米。
产品特性：
泵水力设计独特，叶轮是缩在单独的叶轮室内，连接叶轮室的是压水室，当叶轮旋转时，泵内液体产生强烈的轴向涡流作用，使进口造成真空，出口产生扬程。因而杂质可以从压水室排出，所以它的流道是完全畅通的，其排污效果是其他自吸式排污泵无可比拟的。本单位生产的自吸排污泵机可象一般自吸清水泵那样不需要安装底阀，又可吸排含有大颗粒固体块、长纤维、沉淀物、废矿杂质、粪便处理及一切工程污水物。
（巴赫BACH）
核心价值观
实现顾客：服务顾客是巴赫存在的原因，顾客需求是巴赫发展的动力。
艰苦奋斗：巴赫相信艰苦奋斗能赢得客户的尊重和信任。坚持以奋斗者为导向，使奋斗者得到合理的回报。
自我批评：只有坚持自我批评，我们才能更容易地尊重和合作他人，实现客户、公司、团队和个人的共同发展。
开放进取：积极进取，勇于开拓，坚持开放创新。
诚信：诚信是巴赫公司最重要的资产。巴赫公司坚持以诚信赢得客户。
团队合作：胜利者举杯，失败者互相救人。
公司宗旨
我们的目标是提供满足客户要求的产品，可靠的质量，优越的，经济有效的和有效的服务。
（利润）我们将根据我们事业可持续发展的要求，为每个时期设定合理的利润率和利润目标，而不仅仅是追求利润最大化。
(BACH Bach)
Core values
Achieving customers: Serving customers is the reason for Bach's existence, and customer demand is the driving force for Bach's development.
Hard struggle: Bach believes that hard struggle can win the respect and trust of customers. Persist in the struggler-oriented, so that the strugglers get reasonable returns.
Self-criticism: Only by adhering to self-criticism can we respect and cooperate with others more easily, and realize the common development of customers, companies, teams and individuals.
Open and Enterprising: Actively enterprising, courageous to pioneer, adhere to openness and innovation.
Trustworthiness: Trustworthiness is the most important asset of Bach Company. Bach Company insists on winning customers with trustworthiness.
Teamwork: Winners raise their glasses and losers fight to save each other.
The purpose of the company
Our goal is to supply products that meet customer requirements, reliable quality, superior, cost-effective and effective services.
(Profit) We will set reasonable profit margins and profit targets for each period in accordance with the requirements of sustainable growth of our cause, rather than simply pursuing maximum profit.
进口自吸式无堵塞排污泵产品概述：
进口自吸式无堵塞排污泵,主要由泵体, 叶轮、后盖、机械密封、泵轴、轴承座、进口阀、气液分离管、加水阀门、进、排接管等组成。泵的结构见图。自吸排污泵的工作原理：泵体内设有储液腔，并通过上方的回流孔和下方的循环孔与泵工作腔相通，构成泵的轴向加流外混式系统。泵停止工作后，泵内腔已储有一定容积的液体。当泵起动时，有关当局内的储液在叶轮的作用下，夹带着空气被向上抛出，液体通过气液分离管的网格回流到工作腔，气体被排出泵外，使泵内形成一定的真空度，达到自吸的作用。
Self-priming non-blocking sewage pump is mainly composed of pump body, impeller, back cover, mechanical seal, pump shaft, bearing seat, inlet valve, gas-liquid separation pipe, water supply valve, inlet and outlet nozzle, etc. The structure of the pump is shown in the diagram. The working principle of self-priming sewage pump is that the pump body is equipped with a liquid storage chamber, and communicates with the pump working chamber through the upper reflux hole and the lower circulation hole, forming an axial flow-adding and external mixing system of the pump. After the pump stops working, there is a certain volume of liquid in the pump chamber. When the pump starts, the liquid stored in the relevant authorities is thrown upward with air under the action of impeller. The liquid flows back to the working chamber through the mesh of the gas-liquid separator tube, and the gas is discharged out of the pump, so that a certain degree of vacuum is formed in the pump and self-priming is achieved.
进口自吸式无堵塞排污泵适用范围：
1、环境温度≤50℃，介质温度≤80℃特殊要求可达200℃
2、介质PH值铸铁材质为6--9级，不锈钢为2-13。
3、介质重度不超过1240千克/m3.
4、自吸排污泵自吸高度不能超过规定值4.5-5.5米，吸入管长度为≤10米。
5、自吸排污泵通过能力悬浮颗粒直径为泵口径的60%,纤维长度为泵口径的5倍。
1. The special requirements of ambient temperature (< 50 C) and medium temperature (< 80 C) can be up to 200 (?)
2. Medium PH value cast iron is grade 6-9 and stainless steel is grade 2-13.
3. The medium weight should not exceed 1240 kg/m3.
4. The self-priming height of the self-priming sewage pump should not exceed the prescribed value of 4.5-5.5 meters, and the length of the suction tube should be less than 10 meters.
5. The passing capacity of self-priming sewage pump is 60% of the diameter of suspended particles, and the length of fibers is 5 times of the diameter of the pump.
解决方案：
1.吸入管路越短越好，最长不超过10M。
2.此泵若用于抽吸较稠较粘的浆液后，需清洗泵腔，防止泵内留下沉淀物。
3.自吸泵第一次使用，仍需将泵腔灌满水。
4.常规运行3000小时后，需对水泵进行拆检保养，必要时更换不宜再用的易损件。
5.此泵可定做直联式，同心度高，稳定性增强，亦更为经济，不过维修稍嫌麻烦。
6.环境温度≤45℃，介质温度≤60℃。
7.介质PH值铸铁泵为6～9，不锈钢自吸泵为1～14。
8.通过颗粒最大直径为自吸泵口径的60%，纤维长度为口径的5倍。
9.介质中杂质总重量不超过介质总重量的15%，介质比重不超过1240千克/立方米。
产品特性：
泵水力设计独特，叶轮是缩在单独的叶轮室内，连接叶轮室的是压水室，当叶轮旋转时，泵内液体产生强烈的轴向涡流作用，使进口造成真空，出口产生扬程。因而杂质可以从压水室排出，所以它的流道是完全畅通的，其排污效果是其他自吸式排污泵无可比拟的。本单位生产的自吸排污泵机可象一般自吸清水泵那样不需要安装底阀，又可吸排含有大颗粒固体块、长纤维、沉淀物、废矿杂质、粪便处理及一切工程污水物。
（巴赫BACH）
核心价值观
实现顾客：服务顾客是巴赫存在的原因，顾客需求是巴赫发展的动力。
艰苦奋斗：巴赫相信艰苦奋斗能赢得客户的尊重和信任。坚持以奋斗者为导向，使奋斗者得到合理的回报。
自我批评：只有坚持自我批评，我们才能更容易地尊重和合作他人，实现客户、公司、团队和个人的共同发展。
开放进取：积极进取，勇于开拓，坚持开放创新。
诚信：诚信是巴赫公司最重要的资产。巴赫公司坚持以诚信赢得客户。
团队合作：胜利者举杯，失败者互相救人。
公司宗旨
我们的目标是提供满足客户要求的产品，可靠的质量，优越的，经济有效的和有效的服务。
（利润）我们将根据我们事业可持续发展的要求，为每个时期设定合理的利润率和利润目标，而不仅仅是追求利润最大化。
(BACH Bach)
Core values
Achieving customers: Serving customers is the reason for Bach's existence, and customer demand is the driving force for Bach's development.
Hard struggle: Bach believes that hard struggle can win the respect and trust of customers. Persist in the struggler-oriented, so that the strugglers get reasonable returns.
Self-criticism: Only by adhering to self-criticism can we respect and cooperate with others more easily, and realize the common development of customers, companies, teams and individuals.
Open and Enterprising: Actively enterprising, courageous to pioneer, adhere to openness and innovation.
Trustworthiness: Trustworthiness is the most important asset of Bach Company. Bach Company insists on winning customers with trustworthiness.
Teamwork: Winners raise their glasses and losers fight to save each other.
The purpose of the company
Our goal is to supply products that meet customer requirements, reliable quality, superior, cost-effective and effective services.
(Profit) We will set reasonable profit margins and profit targets for each period in accordance with the requirements of sustainable growth of our cause, rather than simply pursuing maximum profit.
BH
| 配件编号 | 配件名称 | 规格 | 材质 | 单位 | 定性 | 价格(元) | 库存 | 供货期 |
|---|
